The Anker Prime Charger (200W, 6 Ports, GaN) represents the pinnacle of multi-device charging engineering, specifically curated for high-density IT infrastructure, modern workstations, and corporate deployments at SKYRS. Utilizing advanced Gallium Nitride (GaN) circuitry alongside ActiveShield 3.0 thermal management, this desktop charging hub replaces up to six individual power bricks with a singular footprint, radically cleaning up power management infrastructure.
Technical Specifications (All Variants)
Model Reference: A2683 / Anker Prime Multi-Port Desktop Station
Form Factor: GaNPrime Ultra-Compact Desktop Unit
Dimensions: 112 × 76 × 35 mm (4.4 × 3.0 × 1.4 inches
Weight: 563 g (1.24 lbs)
Enclosure Finish: Premium Metallic-Coated Polycarbonate
Input Rating: 100-240V ~ 3.2A-2.5A, 50-60Hz (Universal AC Compatibility)
Safety Compliance: UL, CB, CE, FCC, RoHS certified with dual-insulation protection
Port Distribution Matrix
Total Capacity: 200W Max
USB-C Interfaces: 4 Ports (USB-C1, USB-C2, USB-C3, USB-C4)
USB-A Interfaces: 2 Ports (USB-A1, USB-A2)
Output Operational Power Distribution:
Single Port USB-C Output: Up to 100W Max per port (5V⎓3A, 9V⎓3A, 10V⎓2.25A, 15V⎓3A, 20V⎓5A)
Single Port USB-A Output: Up to 22.5W Max per port (5V⎓3A, 9V⎓2A, 10V⎓2.25A, 12V⎓1.5A)
Dual USB-C Utilization: Simultaneous 100W + 100W output split
Multi-Port Loading (3-4 Ports): Up to 200W distributed intelligently via dynamic allocation algorithms
Max-Port Loading (5-6 Ports): Up to 199W structured output to optimize component longevity
Supported Protocols and Ecosystem Compatibility
The integrated iSmartWare and ChargerLAB protocol controllers allow native negotiation across the following structural architectures:
Power Delivery & PPS: PD 3.0 / PPS (5-16V⎓5A) for ultra-fast charging of enterprise laptops, tablets, and mobile devices.
Legacy Fast Charging: Qualcomm QC 3.0 / QC 5, Samsung AFC, Huawei FCP & SCP, Apple 2.4A, and Universal Fast Charging Specification (UFCS).
Deployment and Installation Workflow
Workspace Positioning
Place the Anker Prime Desktop Charger on a flat, well-ventilated operational surface. Avoid placing it in closed, unventilated compartments or directly behind heat-generating equipment to preserve the efficiency of the GaN thermal dissipation.
Power Infrastructure Integration
Connect the supplied 1.5-meter (5 ft) detachable ungrounded standard C7 2-pin AC power cord into the rear input interface of the charger. Plug the opposite end firmly into a 220V-240V AC wall outlet or a dedicated PDU (Power Distribution Unit) surge protector line inside the SKYRS setup. Ensure the AC cord is fully flush with the device interface to avoid erratic power cycles.
Cable Layout Management
For professional deployment, route the high-wattage cables through desktop grommets or undersurface cable management trays. Organize the cables using hook-and-loop wraps, separating the high-capacity USB-C lines from lower-draw accessory lines to prevent physical tangles.
Configuration and Operational Best Practices
Smart Load Distribution Alignment
When configuring the device ecosystem, prioritize high-capacity loads (such as corporate laptops or large enterprise tablets) on the USB-C1 and USB-C2 slots. These ports operate with optimized priority mapping under dynamic power splits.
Cable Specification Verification
To successfully clear the 100W output threshold on any individual USB-C interface, you must pair the port with an integrated E-Marker chip-enabled Type-C cable rated for 5A/100W+ capacity. Standard low-tier cables will bottleneck negotiation down to 60W or lower.
Dynamic Safe Power Balancing
The ActiveShield 3.0 system routinely runs thermal checks to protect hardware. If the device detects an over-current or over-temperature state, it dynamically lowers the wattage distribution profile across the active lines. To reset standard negotiation parameters after an interruption event, disconnect all loads for 10 seconds and reinsert them sequentially.
Availability and Support Structure
Exclusive SKYRS Provisioning Notice: Deployment, installation, and end-to-end hardware configuration services for all variants of the Anker Prime 200W GaN Desktop Charging Station are strictly available and executed only at SKYRS within the Pakistan region.
